Power Microsilica Gel-Fast Harden

Description

Power Microsilica Gel-Fast Harden

Power Microsilica Gel-Fast Harden is an innovative and advanced product, recognized as one of the strongest and most efficient super pozzolanic micro-silica gels. This product is formulated with a combination of polycarboxylate ether and silica fume, along with additives such as fillers, waterproofing agents, setting accelerators, and polypropylene fibers. Power Micro-Silica Accelerator Gel stands out from other micro-silica products due to its lower consumption rate and superior water-reducing capability.

By adding this micro-silica gel to the concrete mix, the desired workability is achieved, and the slump of the concrete increases, which in turn improves the rheological properties in the plastic state. After curing, the concrete exhibits enhanced mechanical and electrical properties. The high workability of Power Micro-Silica Accelerator Gel enhances the flow of silica fume, catalysts, and water-repellent materials within the mixture, resulting in a more homogeneous and dense paste. After setting, the concrete will have high cohesion and excellent impermeability.

In addition to all the mentioned benefits, this power gel accelerates the hydration process and contributes to faster setting of the concrete.

Features Power Microsilica Gel-Fast Harden

• Accelerates the initial setting process of concrete
• Increases compressive, tensile, and flexural strengths of concrete
• Enhances durability and stability of concrete against freeze-thaw cycles
• Achieves early compressive strength
• Prevents segregation of aggregates and bleeding in concrete
• Reduces permeability to water, chloride ions, and sulfate attacks
• Creates a smooth and uniform paste consistency in concrete
• Prevents cracking in the concrete
• Economical due to low dosage requirements
• Reduces cement content by approximately 15 to 20 percent
• Reduces water-to-cement ratio by up to 25 percent
• Compensates for deficiencies in fine aggregates and fillers for improved paste texture
• Facilitates easy pumping of concrete and reduces wear on equipment
• Provides a smooth and aesthetically pleasing surface
• Increases workability without the need for additional superplasticizers
• Reduces damage caused by improper curing in the early stages
• Compatible with all types of Portland cement
• Significantly reduces water content
• Improves workability and increases slump of the concrete.

More products ; microsilica products

Applications

• Ideal for producing waterproof and impermeable concrete
• Compatible with concrete pouring in sections with high rebar density
• Producing high-durability concrete when reducing the dimensions of structural elements is required
• Suitable for both reinforced and unreinforced concrete pours
• Producing precast components for quicker utilization
• Suitable for structures exposed to abrasion and wear
• Ideal for concrete exposed to freeze-thaw cycles
• Suitable for high-volume concrete pours
• Capable of producing waterproof concrete for tunnels, treatment plants, water transfer channels, and reservoirs
• Ideal for concrete exposed to explosions
• Suitable for concrete exposed to high dynamic loads
• Ideal for industrial hard flooring concrete applications
• Suitable for concrete pouring in areas subject to chemical and corrosive material attacks
• Usable in cold weather conditions
• Producing high-strength, durable concrete
• Ideal for constructing concrete for docks, bridges, bridge decks, reservoirs, and dams

How to use

Power Gel Micro Silica Accelerator can be added to the concrete mix in two ways:

1. Mix the gel with all or part of the water used in the concrete mix, then add it to the dry materials and mix.
2. Power Gel Micro Silica Accelerator can be added to the mix after all other components have been added.

Note: For every cubic meter of concrete, at least 1 minute of mixing is required.

Note: Using more than the recommended amount of this gel can accelerate the setting time of the concrete too much and may negatively affect the final properties of the concrete.

Technical specification table

Color	grey
Specific Gravity	gr/cm3  1/35 –  1/30
Standard	ASTMC-494TYPEF BS EN12390 BS1888 – 122 – 8
PH	8
Chlorine ion	Doesn’t have

 

Package:

25 Kg Bucket